Complete 950cc piston and Nikasil coated barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression. This kit with Italian made piston and rings is an an alternative to Gilardoni kits which can often be in short supply.

Components for one cylinder. See ENA18102 for similar kit made by Gilardoni

 2 in stock

18060102-z 18060102 GU18060102 18 06 01 02
 1806 0102 1806.0102 18.06.01.02

Clamp on Pipercross foam air filter

This K & N foam air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable. Best run dry for road. Fits VHB 24 and VHB 26 Dellorto carbs. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter. Supercedes discontinued S & B air filters

 2 in stock

Rubber sleeved folding riders footpeg, suitable for Tarozzi rearsets and as an upgrade for standard footrests

Folding footrest

 1 in stock

High quality balance pipe or crossover. Finished in polished stainless and made in Mandello to order this H piece has been developed specifically to compliment Mistral silencers and downpipes and is an excellent choice for bikes that will be ridden.

Note that this is not compatible with the original Le Mans downpipes with crosspipe as the centres on this H pipe are too wide to fit them. Will fit Mistral silencers only.

 1 in stock

Chrome plug or bolt cover for M8 socket head bolts, tidies up screw heads

 1 in stock

 23943410 GU23943410 23 94 34 10
 2394 3410 2394.3410 23.94.34.10

S&B air filter. Offset mounting, chromed back, includes clip. Fits Dellorto PHF36 and PHF30 carbs.

This K & N type air filter is designed to offer improved and unrestricted airflow whilst offering adequate filtration. Washable and reusable. Best run dry for road. You may find that a 5-10% increase in main jet size helps to make the most of the increased air flow with this filter. Either ENA14700 or ENA14157 can be used as a breather box to replace the unit in the airbox on round barrel models

 1 in stock

Pair of Tommaselli chromed headlight brackets with anti vibration rubber collars and silver finish aluminium brackets. To fit 35mm and 36mm diameter forks.

 1 in stock

Tarozzi fork brace, this will help prevent forks twisting under heavy cornering and is a good handling upgrade for older bikes.

 1 in stock

Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Smarten up the rear of your V7 with this fenda eliminator kit with includes an LED tail light.

This tail tidy is part of the exciting range of MAS parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks

 1 in stock